Holo Audio Flagship Dual Mono R2R DAC "MAY" Support DSD1024 / PCM1.536M
Welcome for worldwide customers
-Holo Audio Hong Kong
+852 63442556 (whats app & call)
Review form GoldenSound:
May Dac = “The possibility of.”
The May DAC is here! over 3 years waiting and tremendous R&D to achieve a new level of performance and sound quality that sets a new standard. Ultimate endgame DAC. Natural Analog sound with no compromise. Having the best measurements of NOS R2R Dacs. And delivering our intoxicating sound signature that HoloAudio is known for.
- All Level 1 options
- HoloAudio Caps
- Upgraded Fuse
- Remote Control
- DC cable, power cable.
Level 3 (same as KTE)
- 1. 100VA DUAL O-type(not Toroid) FLATWIRE (NOT roundwire) 6N Copper custom hand made audio transformers. (All models)
- 2. All copper wire is replaced with 1.5mm pure occ silver wire. Only L3
- 3. Hand Selected Dac modules to have best measurements compared to averages. Higher dynamic range. Only L3 model.
- 4. CNC Black/Copper shield DAC Module Covers on each module with laser etched KTE logos. Only L3 model.
- 5. Replaced IEC inlet connectors with pure silver/rhodium plated faston connectors at the IEC inlet Only L3 model.
- 6. Fuse is upgraded with world class Red Nano fuse with gold/silver and graphene and quartz filtering materials. Only L3 Model
- 7. Standard Vishay caps are replaced/upgraded with Special made Holo capacitors******unique ONLY to MAY L3 (we have done extensive testing and these prove to provide intoxicating voicing and are beyond subtle improvements over L1/L2)
- 8. Custom made HoloAudio 1000V 1uF caps (replaces standard mundorf evo silver/gold caps)
- 9. Enhanced USB module with Titanis 2.0 circuit
- 10. pure copper Kitsune fox emblem on top panel + remote control
Stereophile 2020 Award A+ in Digital Processors
Stereophile August review
The May DAC (all three models) will also support DSD1024 native and PCM 1.536MHz output! Theoretically it can do DSD2048 and PCM 3.072Mhz however is untested at this time. Also, we have worked hard to reduce the common click noise with all dacs when switching from DSD to PCM. This sound click sound has been reduced significantly with a special circuit design. The May DAC has the new and exclusive USB Enhanced module (L2 and KTE ONLY) which has our FPGA with the new Titanis 2.0 and custom firmware to improve USB Eye Pattern and reduce latency to near zero as well as reduce jitter to very very low levels. The USB module has completely new code written to optimize performance and reduce latency significantly. Low frequency performance (-40db) is also improved. The “enhanced” USB xmos module is twice as powerful/capable as the one that is used in the Spring2.
New improved power supply circuit with high performance multi stage regulation circuit using Rubycon ZLH caps, Panasonic FC, Vishay Caps or L2/L3 models with our exclusive HoloAudio Branded Caps (KTE model unique custom proprietary caps to replace Vishay caps)
We are no longer using common LVDS chipset and are now using a custom 4way circuit that isolates each line which further improves sound quality. such as the MCLK is isolated from data line and this improves jitter spec. Also there are TWO i2s ports in the May dac. Each one can be individually configured pin outs to support all i2s products on the market.
The May is a DUAL mono DAC. so there is a dedicated Dac Module for Left Channel and a dedicated Dac Module for Right Channel. Also each channel is individually powered by it’s dedicated Otype FLATWIRE transformer found in all three models. We have found after careful testing this new transformer type outperforms ALL transformers we have ever tested to this date. Near zero leakage, improved dynamics and overall spectacular performance. They are handmade for this dac specifically and delivery world class performance you would expect.
May DAC also has a new screen on the front that appears the same as the Spring2 on initial glance…. Font size is bigger than Spring2 but smaller than Spring1. Also you can see the CD track-time information is displayed when using spdif inputs!!!. This is done by extracting additional data from SPDIF. This a part of CD red book standard but nobody notices this and often forgets this cool feature or doesn’t know how to extract the data!. This will lead a fashion for other DAC developer to support this feature… customers will surely love this feature albeit subtle. The screen is much better contrast and viewing angles and one of the first things one may notice.
The May also has a front power button now! It’s been a request by many customers and gone are the days of a good old reach around to get the dac to be turned on! As mentioned before above… The DAC has a soft start circuit!! So don’t fret, it takes a moment for it to charge up and pull power without blowing the fuse!! It actually uses the same exact value of fuse that our Spring1 and Spring2 has! But two transformers! If we don’t have a soft start a couple issues can happen… one being a blown fuse from power surge, and another simply having possible pop noises. No chance of these things happening. We have carefully designed the circuit to have a zero compromise design.
Technical Information about our Custom PLL circuit:
More about the May Dac.
- The new generation of linear compensation technology solves the accuracy errors caused by resistor
tolerance, after compensation, reaching a variance of 0.00005% tolerance accuracy.
- Proprietary anti-jitter technology that provides a full amplitude of anti-jitter without increasing noise floor
and other undesirable effects.
- Based on this new generation of technology May “梅” can provide a SINAD of >115dB and a dynamic range
of >130dB, which represents the performance limit reached by today’s most advanced R2R architecture
- Using the ultimate performance of PLL+FIFO technology, provides 0.1Hz Third-Order low-pass ability to
inhibit jitter. It also uses a high-performance femtosecond VCXO as the PLL clock source. Under the premise
of being almost immune to the front-end jitter, it can also lock up to 1.5us-2us @ 1KHz signal with high
jitter. (It can lock up to 1.5us-2us @ 1kHz signal with high jitter on the premise of almost being immune
- Dual Mono DAC L/R channels are independently powered by their own dedicated transformer in the PSU
chassis. This provides better channel separation and more accurate sound stage.
- Official Support USB and I2S up to DSD1024 and PCM1.536MHz sample rate.
- The USB interface uses proprietary firmware with ultra-low latency, a highly reliable data transmission, ideal
USB eye pattern measurements that contributes to 2-4 times higher performance than official firmware.
- Two sets of independent HDMI-I2S input interfaces are provided, and each set of I2S has a four-way
independent circuit, as opposed to standard LVDS chip, making I2S clock signals subject to lower
interference and lower jitter. In addition, each group of I2S inputs can be configured with specific pinout
configuration, making it compatible with most of the HDMI-I2S digital devices on the market.
Dimensions per chassis (2 total): 430 mm (W) * 300 mm (L) * 55 mm (H) additional 12 mm for machined feet (for each part, two of these chassis stacked on each other)
Weight: 18.0 kg Approximately for both Chassis or about 39.68Lbs
Power Consumption: 60W
You may be asking… well what is so special about this DAC? A Discrete R2R DAC with linear compensation…what is this?
There’s an additional R2R resistor network in the May DAC, that compensates the main R2R ladder. It works like trimming, but trimming is to change the resistor value. This additional R2R ladder is digitally controlled and will accurately compensate the resistor tolerance reaching a variance of 0.00005% tolerance accuracy. . For example, the MSB of 16 bits should have the value of 32768, but due to tolerance, it represents 32700 in real world results. Then that additional R2R ladder will compensate 68 into it. Thus it now becomes 32700 + 68 = 32768. What this means is that it’s likely the most precise Discrete DAC on the market with near flawless linearity, lowest THD and highest SNR of any NOS DAC. The sound is simply something you must experience to fully realize how special this DAC is. It’s a patented technology exclusive to HoloAudio. KitsuneHiFi is also HoloAudio USA and proud to bring you this DAC.
This new DAC “May” is the design of a new generation, it’s HoloAudio’s finest technology all designed by Jeff Zhu, the engineer behind these great products. It’s a full discrete R2R type of audio decoder and does not have off the shelf-DAC chip! This is a bespoke custom-designed core DUAL MONO DAC modules that are truly a breakthrough with technology for any DAC chip today. The May is here to achieve new heights, new dynamics and simply a full spectrum of audio to please the aural senses.
May’s input and output interface:
- Digital input interface includes
- Enhanced USB (ground isolation) + Titanis 2.0 circuit + KYCON industrial High retention USB Connector (improved impedance spec) – Proprietary inhouse firmware w/ ultra low latency performance. Ultra low noise voltage regulation
- RCA coaxial
- BNC coaxial
- optical fiber/Toslink
- I2S (HDMI) – improved ultra high performance 4way custom circuit (NOT traditional LVDS chip anymore) backwards compatible
- I2S-2 (HDMI) – improved ultra high performance 4way custom circuit (NOT traditional LVDS chip anymore) backwards compatible
- All digital input interface supports DSD (DOP mode).
- Analog Output interface: single-ended, balanced.
May DAC R2R structure and design + Input/output Stage
Modern and popular delta-sigma type DAC differs from R2R within one clock analog value can recover a sampling point, and the delta-sigma is used to represent an analog signal after passing through oversampling and high-speed digital switching 0 and 1. In comparison, the conversion structure of R2R is most direct and pure, but delta-sigma is essentially a digital chip, high-speed digital signals 0 and 1 switch to the low-pass filter to process the analog signal and this process is prone to various problems, produce digital sound (digititus) and also in the super-sampling process will inevitably cause some ringing and distortion. But DAC R2R structure requires high-precision resistor network which the cost can be very expensive. And the digital delta-sigma DAC chip in comparison is very low cost. Patented R2R technology. This is the first discrete DAC that has Linear compensation and this allows for ultimate music reproduction accuracy. Dual R2R ladder network with advanced architecture for PCM, and Dual Resistor Ladder network with optimized architecture for DSD!
I/O stages: There is an Op Amp used for input stage and discrete component used for the output stage. The discrete output stage is working in pure class A. It’s BiPolar Junction Transistors, direct coupled.
A common question we get…” Why do you use an Op amp at the input of the DAC?”
The input stage with an opamp is a good choice. It has a paired transistor input by the nature it is manufactured. But an opamp for the output stage is limited due to it’s size and the thermal capability. Also, no one will offer an opamp with class A output as it’s efficiency is so low. So an opamp used as input and discrete output combined together will have an advantage. It doesn’t mean that all discrete is not good. Actually, if we need to achieve enough low distortion. It needs at least 30-40 transistors. Which not only will it be huge and waste of space but it will also be too costly. I mean, to beat the opamp’s performance, a simple discrete architecture is not possible, although an all discrete design looks beautiful.
We use opamp+discrete architecture for the amp parts of May. Opamp is used for the input stage, discrete is used for the output stage. All the transistors in the opamp are in the same die, then it is matched by nature. This is key because by now, there are few choice for low noise matched pair transistors but an opamp has plenty of them inside. The Output stage is discrete because it generates a bit of heat. We need a class A output stage. So you can see May is very hot compared to other DACs. An opamp output simply can’t handle that power.
The true balanced DUAL MONO circuit design
XLR is using all of the circuit and RCA is just using half of them. The balanced output has better performance (THD, noise) and also better common mode rejection rate. If you’re listening environment contains interference, either from AC power or from EMI/RF then you will find a full balanced system can really help significantly.
With diverse and flexible sampling mode conversion mode
1: NOS mode: has no digital oversampling, the raw data is directly converted to analog. Because digital oversampling will produce time-domain distortions, such as ringing, NOS avoids these problems. Generally NOS mode’s other performance indicators have a significant impact, but the Spring 2 is designed to allow top performance while in NOS mode.
2: OS mode: PCM is over sampled to PCM at a higher frequency, DSD is over sampled to DSD at a higher frequency, and then digital is converted to analog.
3: OS PCM mode: in either PCM or DSD the data will be oversampled to PCM and then digital is converted to analog.
4: OS DSD mode: in either PCM or DSD the data will be oversampled to DSD and then digital is converted to analog.
What are the May’s sound characteristics? :
One of the strong points of the spring is the spatial sounds stage presentation. It’s very wide and precise. It never sounds congested like many DACs. The high end is very detailed and never harsh sounding. It has the R2R goodness that many have come to know and love. R2R has almost a cult like following and this DAC will surely become a sought after DAC. Everything comes effortlessly for this DAC. Bass is layered and textures, quite full and present without ever masking over the sweet mid tones that are produced. One special thing about the May is its amazing voltage regulation circuitry that better than 0.2uV output noise! This along with the FLATWIRO-core transformer helps regulate the purest power which translates to audio clarity and accurate reproduction. It must be heard to appreciate and come to love its sound.
English User Manual HERE
Chinese User Manual HERE
v31.42 Firmware Gen2.1 ONLY :
Fixed volume version: HERE
Adjustable volume version: HERE
Previous drivers: HoloAudio Drivers – Win7/8/8.1/10 – v.5.20
Welcome for worldwide customers
-Holo Audio Hong Kong
+852 63442556 (whats app & call)